chainlink apple chainlink valor chainlink stretcher Use THIS to Pull a FENCE
Hey everybody. This is an area of our property that we are getting fenced in to be a chicken run, so today Im going to show you how were going to string up this first part of the fence. Rather than try to wrap a fence all the way around the post, were going to individually stretch fence from one post to another, cutting it at each intersection. One thing you need to take into consideration when installing your fence is if there is any slope on the property. You dont want to attach your fence perfectly plumb onto this post and then find out you have even a one percent grade going up towards your other post because then youre going to have problems aligning the entire fence, so what were going to do is temporarily hang this post with some very loose staples so that we can determine what angle it needs to be at and then proceed from there. Okay, so what were using as a guide for now, the fence is still extremely loose but were making sure that the bottom is flush and then well put in this loose tack up top and then well start to arrange things so that we can pull it tighter. So trying to do everything as taut as we can by hand, this is as far as we are able to get. As you can see, theres an awful lot of slack still in there and as you can see by looking at the fence in relation to this pole were going over about 6 inches from center, closer to 8, than where we are in center down at the bottom and that is showing the elevation change from front to back. So now let me show you what were going to do to tighten this up. Now just to explain to you a couple of the tools that we need in order to stretch the fence. Theres probably a hundred different ways to do this. Ive seen people do it using a wench on their vehicle, theres just so many different ways. Were going to make use of the tools that we have and thats comprising of a tension bar that you can find in the chain-link section of your hardware store, a fence puller and both of these are designed to help spread the pressure out on the fence because the next piece of equipment is the Come-Along and its what were going to use to crank the fence and pull the tension on it, but if we were to just have one point of contact on this fence were going to damage it and probably pop some of the welds. So, by combining that with the tension bar and the fence puller we can spread that force out across the fence on many different points and get a lot more tension before we worry about causing any damage to the fence. Okay, so the next option that really presents itself to you is where are you going to connect to this fence and what are you going to connect to so that you can stretch? If youre in a big open field, probably the only thing thats available to you is the corner post. You can see in our case that theres a cedar tree behind here, but as the image makes it look, though its a little more extreme on the image, the cedar tree is in front of the fence, meaning that if we tried to pull tension on the fence toward the cedar tree, were going to end up about a foot away from the post that were trying to connect to. If you had a point of contact that were, as it is in the picture, to the left of the fence, then you could connect to that and pull the fence from behind the post. The other option to you is to bring your tension bar and fence puller out in front of the post, probably a good 3 or 4 feet, if not more, and then pull tension and connect your Come-Along to the post, pulling the fence to the post. Now when you do that, youre going to have a slack area between where your Come-Along attaches to the fence and the post but the idea here is, by the time that you release everything, the little bit of slack that was there is not going to really present itself and you will be able to have a tight fence. Another option that you always have is to move your tractor in place and create an anchor point for you to be able to go on. So, I like this option better because Id rather not connect to the corner post because of the slack that it leaves behind, so by having my tractor over there, I can pull and get the tension that I need on the entire fence. One note of caution here, as you connect everything, make sure that whatever you anchor to is at the same height as your anchor point on the fence. That way you dont end up trying to pull up or down on the fence. Alright, connecting the tensioner is easy enough to do. Youre going to want to intertwine it into your fence. Im going to go two horizontals on one side of the tension bar and then two horizontals on the other side and connect it all the way down. So as you can see, the point of this is to give you something to pull on thats not going to easily bend because you have that width of the tension bar to pull against. Okay, so now that you have your tensioner in your fence, youre going to attach the fence puller to it. Just do your best to make sure that youre in the middle of it so that youre not too high or too low, and youre just going to hook on just like that. Now Ive already connected to my anchor point and Im just going to connect onto here. Now our goal is simply to ratchet the Come-Along slowly until we start tensioning the fence and then make sure that everything is aligning the way that we want. You can see theres still a slight bend in the fence, but this is as tight as were going to be able to get it without damaging the fence material itself. If this were something like a barbed wire or just a field wire fence then we would be able to get this much more taut. In this case, what well do is secure these nails, or staples onto the fence post and then use t-posts to support the structure throughout the span. One thing you really need to remember to take into consideration is what direction your fence is pulling to where youre going to put in the staples. You can see, this is the end of the fence that we had the Come-Along attached to so the fence is wanting to go back that way, so we have the staple on the left side of the vertical wire to help control that desire for the fence to go that way. Okay everybody, I hope that gives you some sense of what you need to do to be able to stretch a fence. As with so many other projects, the next step is going to have to wait for another payday, but now you have the essential information that you need to go forward and start your project. If you have any questions or comments, please go ahead and leave them below and as always, thank you for watching. Comealong - Fence Stretcher Bar - --- Visit for more hobby farm activities. How to Install a Fence: Homestead Help. Pulling a section of field fence using a fence puller, tension bar, come-along and tractor! homesteading familyfarm fencing chickens fencing,chickens,familyfarm,
movimientoantipiquetero.com.ar