chainlink sizesDIY / Building a wooden fence using galvanized fence posts part 1.

how do i buy chainlink why to buy chainlink chainlink sizes DIY / Building a wooden fence using galvanized fence posts part 1.

hello youtubers many here coming to you from Annies how-to workshop with another project that Im doing at my home basically Im building up the fence on the side of the house after the property lines were resurveyed between me and the neighbor because originally her fence thats way back there which is actually this one right here on the other side was actually 2 feet into my property so we had to go ahead and readjust that and give me back my two feet so now Im getting down to actually putting up my own fence and I chose to go with using galvanized posts instead of the 4 by 4 pressure treated because I want a more permanent result so basically in the future if I ever have to replace the boards its just the board that wont have to dig the holes and reset the posts the post was already be there which makes it a whole lot easier and also the method that I used by doing it this way will make sure that the fence last way more a lot longer probably like good 10-15 years easy why because Im making my own frame instead of the pre prefabricated frames that are chintzy and thin and the pickets dont last long because its thin and whatnot so this is what Im done all right so basically the posts are set at 8 foot centers with the exception of the very back over there I got about a two-foot space there on that side right there but other than that the gap between here and here and there like I said is 8-foot centers on the posts I dug the holes 27 inches to allow a couple more inches for gravel at the bottom and then setting the posts at 24 inches using quikrete concrete you know 3,000 psi concrete which sets pretty quick because here in Florida you know you got to do this outside and of course you know as always were in the rainy season so theres always chance for rain in the afternoon so we got to play it by ear and try to knock it out as quick as possible so like I said post is set at 8 foot centers hole dug 27 inches deep for a couple inches of gravel at the bottom mix concrete poured in there set it with the post level and after that give it a day to cure come back and start installing these brackets so let me get over here and show you what kind of breakfast Im talking about so these brackets here it made for attaching wood to galvanized post as you can see I use some outside lag screws and also on the bottom right here I put in some deck screws going up that just has added security you know just to make it more sturdier this here is held this clamp is held by this 13 millimeter nut with a what looks like a its a rounded head screw which on the wood what I did was I drilled a hole to make a recess for the head so that way I can end up getting the wood will end up being flush okay like that you can see that its nice and flush on the on the bracket takes time to do it right obviously but hey the end result is a professional-looking job that you can be proud of on this side here as you can see I went ahead and use these brackets here that are made for two by fours to attach it to the post of this existing fence with my neighbor and that gives it a nice resting place using number eight one-inch text screws to hold them and three places one on this side one on the opposite side and one underneath also I shored that up because the fence post wasnt leveled so I braced it up against the house just to make sure that the top is leveled so I can run this support here all the way across and what I end up doing I bought 10 foot sections to do these last two since you know its 8 for Center and then extra two feet overhanging I just bought a 10 foot section that we get a nice solid piece going across and the Bs here these supports I measured from top to bottom and split the difference and I believe theyre like thirty to thirty two and a half inches from the bottom kick board to the center and then to the top but I did have to make some adjustments for the top because I ran out of 4x4 at the end over there on the top right there so if you can see itll focus yeah if you can see right I know my fingers blurry so you know what let me just come over here and show you okay so basically you can see theres the top of the 4x4 so I had to drop the bracket down enough to where the screws could attach to it and that made me drop all the rest of the brackets on the top down which is fine you know it doesnt matter because the pickets gonna go on this side here when Im standing so this whole side is gonna be smooth with pickets but you can see that it does a nice job also this bottom kickboard is a two by six pressure-treated all the supports 2x4 is a pressure-treated okay just to give you an angle of how straight everything is like I said you take your time measure everything do it right and its gonna come out looking excellent like I said the back measurement from the corner of the house there to here okay is exact going across that way I can get make sure its nice and square and right here for the front Im gonna end up putting two gates which Im gonna build using the pressure-treated 2x4 and adding some you know some supports cross braces to make it more sturdy and and that will be on the next upcoming video well thanks for watching guys as always please like comment and subscribe if you havent done so and Ill catch you guys on the next one all right take care In this video, I show you guys how im constructing my wooden fence using 2 3/8 diameter galvanized fence posts and metal post to wood brackets see link below. This is a long lasting build because only the wood will need to be replaced in the future after they become too old. If you buy the brackets using this link, Ill get a little help from amazon. 160 Foot Fence Job: Metal End Post Brackets: Metal Post Brackets: Metal Galv. Fence Post: BRANDON,